Faculty of Industrial Chemistry and Environmental Engineering, Politehnica University Timisoara, 6 V. Parvan Blv, RO-300223 Timisoara, Romania Show 2 National Institute for Research & Development in Chemistry and Petrochemistry—ICECHIM, 202 Spl. Independentei, RO-060021 Bucuresti, Romania 3 Centre of Advanced Research in Bionanoconjugates and Biopolymers, “Petru Poni” Institute of Macromolecular Chemistry Iasi, Grigore Ghica Voda Alley, No.41 A, 700487 Iasi, Romania 4 Institute of Chemistry Timisoara of Romanian Academy, 24 Mihai Viteazul Blv., RO-300223 Timisoara, Romania * Author to whom correspondence should be addressed. Appl. Sci. 2020, 10(23), 8440; https://doi.org/10.3390/app10238440 Received: 18 October 2020 / Revised: 20 November 2020 / Accepted: 22 November 2020 / Published: 26 November 2020 (This article belongs to the Special Issue New Trends in Functional and Multifunctional Advanced Materials) Download Download PDF A closed-cycle technology regarding the use of an exhausted Pd-based adsorbent as a photocatalyst in the degradation process of phenol is presented. Pd (II) represents a precious metal of great economic importance. Its obtained from natural sources become more difficult to achieve. Therefore, also considering the regulations of the “circular economy,” its recovery from secondary sources turn out to be a stringent issue in the last years. Pd(II) ions are removed from aqueous solution through adsorption onto Florisil (an inorganic solid support—magnesium silicate) impregnated with Cyphos IL 101 (trihexyl tetradecyl phosphonium chloride). It was observed that the presence of the ionic liquid (IL) in the adsorbent structure doubles the adsorption efficiency of the studied materials. The newly obtained Pd-based photocatalyst was exhaustively characterized and was used in the degradation process of phenol from aqueous solutions. The phenol degradation process was studied in terms of the nature of the photocatalyst used, time of photodegradation and solid: liquid ratio. It was observed that both the presence of IL and Pd lead to an increase in the efficiency of the phenol degradation process. The new Pd-based photocatalyst could be efficiently used in more cycles of phenol photodegradation processes. When is used as a photocatalyst the Florisil impregnated with IL and loaded with 2 mg/g of Pd, a degree of mineralization of 93.75% is obtained after 180 min of irradiation of a phenol solution having a concentration of 20 mg/L and using a solid:liquid ratio = 1:1. Keywords: Palladium (Pd) is one of the precious metals of great economic importance. Its specific physical and chemical properties make it useful in many fields such as electrical and electronic industries, corrosion-resistant materials, jewelry or as catalysts in various chemical processes [,]. Due to its importance and the rare ore deposits which make a high price for this metal, it is essential to develop efficient recovery methods for this element, especially from water containing trace amounts of Pd. There are numerous methods for palladium recovery from different waste, such as solvent extraction [,,], ion exchange [,,], electrometallurgy [] and adsorption [,,]. From all the mentioned methods, adsorption proved to be the most efficient for the recovery of precious metals from aqueous solutions due to easy operation, the existence of versatile adsorbents (such as activated carbon, chitosan, calcium alginate, graphene oxide, titanate nanotubes, etc.) and high efficiency even in case of solutions containing trace amounts of metal ions [,,,,,,]. Since the ionic liquids (IL) were successfully used in the liquid–liquid extraction of precious metals [,], in the last years, new attention has been given to the use of ionic liquids for obtaining different adsorbents for palladium removal from aqueous solutions [,,]. The immobilization of the ionic liquids in suitable solid support prevents the drawbacks of the liquid–liquid extraction, such as the loss of the ionic liquid in water and a possible occurrence of an ion-exchange between the metal ion and the cation of the ionic liquid. Through impregnation of the ionic liquid onto a suitable solid support, higher efficiency in the removal process of metal ions from aqueous solutions is achieved because it favorably combines the properties of ILs with the advantages of the solid supports [,]. In a previous study, the adsorption performance of the Florisil impregnated with Cyphos IL 101 (trihexyl tetradecyl phosphonium chloride) in the removal process of Pd(II) ions from residual solutions was studied []. It was observed that the impregnated Florisil with Cyphos IL-101 develops a maximum adsorption capacity in the removal process of Pd(II) ions from an aqueous solution of 126 mg/g, which is two times higher than the adsorption capacity developed by the raw Florisil []. The Circular Economy Action Plan of EU intends to close the loop of product lifecycles through sustainable consumption and production by improving waste management with greater recycling and reuse in order to create benefits for the environment, the economy and the society []. In all the adsorption studies, the major problem is, “What happened with the exhausted adsorbent?”. Very few papers answer this question. In order to respond to the European Union targets and to create benefits for the environment, economy and society and to respond to this frequently asked question in adsorption processes treatment, the aim of this paper is to study the possible use as a photocatalyst of an exhausted adsorbent from the removal process of Pd(II) ions from aqueous solutions. Many Pd-based composites are synthesized and studied as photocatalysts in various degradation processes [,,,]. However, in all cases, the obtaining method is very complicated, involving several steps of synthesis and using expensive resources. By using a waste resulted from another process as a photocatalyst, the Pd ions from secondary sources were capitalized. Consequently, the use of Pd ions from prime materials is avoided, which led to a minimization of the cost of treatment. The method proposed in this paper represents a closed cycle technology, and it is advantageous from both economic and environmental protection perspectives. The Pd-based photocatalysts obtained through Pd adsorption onto Cyphos IL 101 impregnated Florisil have been used in the degradation process of phenol from aqueous solutions. The phenolic compounds deserve the entire attention because it is found in many industrial wastewaters and even in some water resources due to the fact that it is used in several industrial branches. At concentrations higher than 0.001 mg/L, it is very toxic and carcinogenic [,,,]. The technologies utilized for removing phenols from industrial wastewater could be classified as destructive or non-destructive. The non-destructive technologies (distillation, adsorption, extraction, membrane separation) are feasible when the main concern is the recovery of the phenolic compounds. Otherwise, the destructive technologies (chemical or electrochemical oxidation, advanced oxidation processes, biological treatment) are more feasible due to the fact that not implies the transport of pollutants from one phase to another. Each of these technologies has advantages and drawbacks, and the feasibility of utilization one or another removal process of phenolic compounds must take into account the initial concentration, the pH and salinity of wastewater and the costs of treatment. Advanced oxidation processes (ozonation, wet air oxidation, Fenton oxidation, photo-assisted catalytic oxidation) are feasible in the tertiary process of water treatment in order to remove recalcitrant organic pollutants from water and to reach the physicochemical characteristics required by the regulations. The Pd-based photocatalyst was obtained through Pd(II) adsorption from residual solution onto the Florisil impregnated with Cyphos IL-101. The Florisil and the Cyphos IL-101 were purchased from Sigma–Aldrich, Darmstadt, Germany. The adsorption of Pd (II) ions was studied in a previous work, and the dependence of the maximum adsorption capacity of the impregnated Florisil function of solid:liquid (S:L) ratio, pH, contact time and initial concentration of the Pd(II), was established []. It was put in evidence that the ionic liquid (Cyphos IL 101) enhance the adsorption capacity of Florisil in the removal process of Pd(II) ions from aqueous solutions. The adsorbent was obtained through impregnation of Florisil with trihexyl tetradecyl phosphonium chloride using the ultrasonication method of impregnation. Then, 0.1 g of IL was impregnated onto 1 g of Florisil. The sample was entitled F-IL). The maximum adsorption capacity developed by F-IL, of 133.3 mg/g, was obtained in the following conditions: solid:liquid ratio (S:L) of 2 g/L, pH = 3 and stirring time of 60 min []. Therefore, in the present paper, the same conditions were used to obtain the Pd-based photocatalyst. Were prepared higher quantities of photocatalyst containing different amount of Pd ions (1 mg Pd /g of F-IL—the sample being entitled F-IL-Pd1 and 2 mg Pd/g of F-IL—the sample being entitled F-IL-Pd2, respective). The used photocatalyst was analyzed by Fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and transmission electron microscopy (TEM), which was coupled with energy-dispersive X-ray analysis (EDX) and by XPS analysis. The FTIR spectra (KBr pellets) of the samples were recorded on a Shimadzu IR Prestige-21 FTIR spectrophotometer (Shimadzu, Kyoto, Japan) in the range 400–4000 cm−1. SEM micrographs were recorded using a Quanta FEG 250 microscope (Thermo Fisher Scientific, Waltham, MA, USA). TEM micrographs were obtained using an FEI Tecnai F20 G2 TWIN Cryo-TEM (Thermo Fisher Scientific, Waltham, MA, USA). Initially, the samples were ground to reduce the size of the particles so as to make them compatible with TEM analysis. The powdered samples were placed over lacey carbon copper grids. After removing the excess powder, the samples were analyzed. The scanning transmission electron microscopy (STEM) feature of the microscope, together with the EDX detector (X-MaxN 80T model from Oxford Instruments, Abingdon, UK), allowed identifying elements present in the sample. X-ray photoelectron spectroscopy (XPS) was performed on a KRATOS Axis Nova (Kratos Analytical, Manchester, UK), using AlKα radiation, with 20 mA current and 15 kV voltage (300 W). The XPS survey spectra for the Pd-based photocatalyst sample were collected in the range of −10–1200 eV with a resolution of 1 eV and a pass energy of 160 eV. The high-resolution spectra for all the elements identified from the survey spectra were collected using a pass energy of 20 eV and a step size of 0.1 eV. Data were analyzed using the Vision Processing software (Vision2 software, Version 2.2.10). The binding energy of the C1s peak was normalized to 285 eV. 2.2. Application of the Pd-Based Photocatalyst in the Degradation Process of PhenolThe obtained Pd-based photocatalyst was used in the degradation process of phenol from aqueous solutions, using a photoreactor PhotoLAB B400-700 Basic Batch-L (provided by Peschl-Ultraviolet, Mainz, Germany). The photocatalytic effect of the obtained Pd-based photocatalyst containing different amount of Pd loaded (F-IL-Pd1—impregnated Florisil with IL and 1 mg Pd/g and F-IL-Pd2—impregnated Florisil with IL and 2 mg Pd/g) was compared with the effect of raw Florisil (F) and impregnated Florisil with Cyphos IL-101 (F-IL). A well-defined quantity of the photocatalysts (0.7 g) was treated with 700 mL of phenol solution containing 20 mg/L phenol. Initially, the phenol solution was stirred for 30 min with the photocatalyst in the dark in order to achieve the adsorption–desorption equilibrium between the phenol and the surface of the photocatalyst. After this time, the sample was irradiated for 3 h with a UV-vis lamp type TQ 150. The samples were collected at different time intervals (5, 15, 30, 45, 60, 120 and 180 min), and the photodegradation profiles of phenol were monitoring by realizing the UV-vis absorption spectra using a Varian Cary 100 spectrophotometer (Agilent Technologies, Santa Clara, CA, USA). The degradation degree of phenol was determined from the absorbance recorded at λ = 270 nm, which is one of the two maximum local excitation bands of hydroxyl-monosubstituted phenyl: Degradation degree (%) = Ai270− At270Ai270100 where Ai270 is the initial absorbance of the phenol solution, recorded at 270 nm and At270 is the absorbance of the solution after time t, recorded at 270 nm.To determine both the degree of phenol degradation and the degree of mineralization, total organic carbon (TOC) was measured by using a TOC analyzer (provided by Shimadzu, Kyoto, Japan). Experiments were triplicate, and the results are presented as a mean. The phenol degradation efficiency was determined as a function of the nature of the used photocatalyst and the S:L (solid:liquid) ratio. 3. Results and Discussion3.1. Characterization of the Pd-Based PhotocatalystThe FTIR, SEM, TEM and XPS analysis were used to prove the fact that the studied solid support, Florisil, was impregnated with the studied IL, Cyphos IL-101. This structural characterization was useful to understand what happened with the solid support during functionalization and which is the reason for its efficiency increasing, and how IL and Pd ions are bounded onto the Florisil surface in order to be sure of the photocatalyst stability. The FTIR spectra of the studied photocatalysts are presented in . From the FTIR spectrum, the impregnation is confirmed by the appearance in the spectrum of the solid support of the vibrational bands characteristic for the ionic liquid, namely: the intense bands between 2950 and 2800 cm−1 occur due to –CH3 (methyl) and –CH2– (methylene) vibrations. The SEM images are presented in . From the SEM images, it can be observed that the Florisil particles before impregnation are in various sizes and shapes, with many microcracks and network defects. After the impregnation, the surface of the Florisil particles is much more uniform. It can be observed the distribution of the ionic liquid particles on their surface by filling the microcracks. After Pd adsorption, the particle surface is very compact; Pd (II) adsorption is observed as a coating on the impregnated Florisil particles. In are presented the bright-field transmission electron microscopy (BFTEM) images of Florisil after impregnation with Cyphos IL-101 and the Florisil after impregnation and Pd(II) adsorption. It can be observed the Florisil particles with the uniform distribution of the IL in the pore structure (the black spots represent the IL particles which fill the pores of the Florisil) (a). After Pd adsorption, the surface is very compact due to its coating with Pd ions (b). The impregnation of Florisil with trihexyl tetradecyl phosphonium chloride is proven by the EDX spectra (), where besides the specific peaks of Florisil (Mg, O, Si), the specific peaks for the used ionic liquid (C, Cl and P) can be observed. For the sample obtained after Pd adsorption characteristic peak of this element is observed, evidencing its adsorption onto the studied material. In order to establish the elemental composition of the sample that will be used as a photocatalyst (Florisil impregnated with Cyphos IL-101 and loaded with Pd ions), the XPS wide scan was used (a and ). The XPS wide scan spectrum proves that the Florisil (which is a magnesium silicate with trace concentration of sodium) was impregnated with the studied IL (Cyphos IL-101—trihexyl (tetradecyl) phosphonium chloride) and also it could be observed the presence of the Pd ions. By analyzing the high-resolution spectra of the elements, XPS allows the identification of the chemical structure. The high-resolution XPS spectra for C 1s and Pd 3d were analyzed in detail for the Pd-based photocatalyst (b,c). The signal corresponding to C 1s was divided into two distinct components corresponding to the Caliphatic at 284.5 eV and Chetero at 286.6 eV. The signal corresponding to Pd 3d was decomposed into two distinct components corresponding to the Pd2+ at 337.2 eV and to the Pd4+ at 338.5 eV (). 3.2. Application of the Pd-Based Photocatalyst in the Degradation Process of PhenolThe characterized materials were used as photocatalysts in the degradation process of phenols from aqueous solutions through UV-vis irradiation. From the characterization section, it was observed that the Florisil support after IL impregnation presented a higher available active site, which led to a higher adsorption degree in the removal process of Pd ions from aqueous solutions []. The exhausted adsorbent resulted after Pd adsorption presented a more compact surface. This means that the sample with Pd content presents higher stability, and it is expected to present also a higher photocatalytic activity. The photocatalytic activity of the studied sample was determined in the degradation process of phenol from aqueous solution through UV-vis irradiation. 3.2.1. Influence of the Photocatalyst NatureUV-vis molecular spectrometry allows both qualitative and quantitative analysis. The correlation between the UV absorption bands and the structure of the compounds (both for phenols and for the products resulting from the oxidation of phenols), so the qualitative analysis is a fast and economical identification technique. The shifting of the absorption maxima at a certain wavelength gives information about the functional groups that appear or disappear at a certain time of reaction. The UV-vis spectra of phenol at a different time of the photodegradation process for all the studied materials are presented in . Initially, the phenol solutions were stirred for 30 min with the photocatalyst in the dark to achieve the adsorption–desorption equilibrium between the phenol and the surface of the photocatalysts. It is noted that in all the cases, the adsorption profile of phenol does not undergo any changes during this time. After the irradiation starts, a hyperchromic effect and a hypsochromic (blue shift) effect of the absorption maximum occur. This means that the photodegradation process of phenol started, and the intermediate compounds are forming [,]. At higher irradiation time occur the hypochromic effect when impregnated Florisil and impregnated Florisil and loaded with different amounts of Pd are used as photocatalysts. The degradation degree of phenol versus the photocatalyst nature at two different treatment time is presented in . It is noted that both the presence of IL in the catalyst structure and the Pd leads to an increase in the degree of phenol degradation from aqueous solutions. In addition, increasing the amount of Pd from the catalyst has a positive influence on the process of phenol degradation. Further studies were performed using F-IL-Pd2 as a photocatalyst. Maybe a 10% increase of efficiency does not represent a significant increase, but it is a great increase taking into account the fact that F-IL is a prime material that could be used for Pd adsorption, and F-IL-Pd is a waste resulted from another process. Furthermore, if the photocatalyst contains Pd ions, it represents much higher stability in the degradation process of phenols because Pd ions are bounded on the IL and, in this case, is avoided the degradation of IL from the surface of Florisil during the photolysis process. If it is used as photocatalyst only the F-IL the TOC concentration increase during the treatment process, which suggest that a part of IL from the Florisil surface is degraded by the UV-vis irradiation, so the efficiency of this material decrease continuously, especially when is used in more cycles of treatment until it present, no photocatalytic activity. Furthermore, the increased efficiency of the F-IL-Pd is underlined by the fact that this efficiency for the phenol degradation is obtained much quickly (at 120 min) than in the case of using only F-IL as photocatalyst when this efficiency if obtained only after 180 min of treatment. This means that a shorter time is needed for treatment, which leads to decreasing treatment costs. 3.2.2. Influence of the S:L RatioFrom the economic point of view, it is desired to use as little photocatalyst amount as possible. For this reason, it is important to know which is the optimum amount of photocatalyst which could be used with good results in the degradation process of phenol from aqueous solutions. The degradation degree of phenol versus the S:L ratio is presented in . With the increase of the S:L ratio, the efficiency of the process of phenol degradation from aqueous solutions increase. Further increase of the photocatalyst amount did not lead to a higher efficiency increasing; therefore, it is not recommended to use an S:L ratio higher than 1:1. 3.2.3. Influence of the Photocatalyst ReuseAn important factor that characterizes a photocatalyst is its stability. It is desired that after a treatment process, the photocatalyst to be recovered and reused in other treatment processes, with the same efficiency to minimize the treatment costs. The photocatalyst obtained by Pd adsorption on IL impregnated Florisil showed stability in the sense that the Pd ions were not detached from the solid support following a photocatalysis process. This was determined by analyzing them in the solution resulting from the photocatalysis process when a concentration below the detection limit was obtained. At the S:L = 0.5:1, after a photocatalytic process, the catalyst was reused in two new degradation processes of phenol from aqueous solutions. It is noted that the efficiency of the photocatalyst decreases by 5% after the first cycle because a part of the IL impregnated onto Florisil is degraded by the UV-vis irradiation. In the further cycle, the efficiency of phenol degradation remains constant (). These results underlined the efficiency of using as photocatalyst of F-IL-Pd compared with the sample of F-IL, where the probability of IL degradation from the Florisil surface is much higher. Even if a part of IL is degraded from the surface of the photocatalyst, the efficiency of the Pd based photocatalyst is not influenced only by 5% because the Pd ions are still coating the surface of Florisil. As it is mentioned in the literature, the photoirradiation led to the greater deposition of Pd ions onto the surface of the solid support [,,]. This good deposition of Pd ions onto the surface of Florisil, even after one photodegradation process, can be seen from the BFTEM image and EDX spectrum of the reused photocatalyst presented in . From the BFTEM images, it can be observed that a part of IL from the Florisil surface is degraded (the black spots are in a smaller amount), but there is still a very good coating with the Pd ions. This conclusion can be raised from the EDX spectrum where the peaks specific for the studied IL (C, P and Cl) are not so evident, but the Pd ions are very well-identified. 3.2.4. Mechanism of Phenol Degradationpresents the kinetic plot (C/C0 at λ = 270 nm vs. time) of phenol photodegradation. At different times of contact, the UV-vis absorption profiles of solutions together with the measured TOC concentrations were presented. The UV-vis absorption profiles of solutions allow making qualitative analysis for identification of the intermediate compounds of phenol oxidation. From the kinetic study and the absorption profiles at different time intervals, as well as by the correlation of our results with results reported in the literature, a mechanism of phenol degradation was proposed [,]. At the same time, the TOC was measured in order to determine the degree of mineralization, not only the photodegradation degree of phenol. It can be observed that during the period of establishing the adsorption–desorption equilibrium between the phenol and the surface of the photocatalyst, it is adsorbed about 10% of the phenol present in the solution. At the start of the UV lamp, a change in the sample absorbance profile is observed due to the hyperchromic effect. This effect suggests that phenol passes into degradation intermediates: catechol, hydroquinone and p-benzoquinone [,]. Up to a 30 min irradiation time, there is no mineralization of these intermediate compounds. This can be seen from the TOC analysis, which shows that even after 30 min of irradiation, the TOC concentration is approximately equal to the initial TOC. Or it is possible that the TOC concentration to remain constant because a part of the IL is detached and degraded from the surface of the Florisil. After this time, in the sample spectrum appear a decrease in absorbance (hypochromic effect), so we can conclude that the process of mineralization has begun, besides the photodegradation process, also proven by the TOC concentration which after 60 min has reached a value of 2.69 mg/L (). By further irradiating the solution in the presence of the photocatalyst, the aromatic ring breaks with the formation of aliphatic organic acids with the short molecule (maleic acid, oxalic acid, formic acid) [,]. Its formation is indicated by the hypsochromic effect (a blue shift) by displacing the maximum adsorption from 270 nm to 265 nm. After 180 min, the TOC is 1.1 mg/L, which means a 93.75% efficiency of mineralization (). Comparing the performance of the studied materials with other photocatalysts reported in the literature () could be concluded that the studied materials, which actually consist of a waste resulted from other processes, presents good photocatalytic activity in the degradation process of phenol from aqueous solutions. 4. ConclusionsThe exhausted adsorbent could be efficiently used as a Pd-based photocatalyst in the degradation process of phenol. The presence of the IL on solid support increases the adsorption efficiency of Pd ions from aqueous solutions. In addition, it was found that both the presence of ionic liquid and Pd (II) ions result in an increase in the efficiency of the phenol degradation process. Furthermore, increasing the amount of Pd (II) from the catalyst structure and increasing the S: L ratio has a positive effect on the degradation process. The obtained photocatalyst could be efficiently used in several cycles of degradation processes. A part of the IL from the Florisil surface is degraded during the first process of photodegradation, but at the same time, the Pd ions are more fixed on the solid support. The efficiency of the catalyst decreased only by 5%, and then the efficiency is maintained. These results underlined the efficiency and stability as photocatalyst of the sample F-Il-Pd compared with the sample F-IL in the degradation process of phenol from aqueous solutions. The results of the present manuscript underline the efficiency of waste resulted from an adsorbent process to be used as a photocatalyst. These results are in the frame of the closed cycle technology responding to the actual need of circular economy. Conceptualization, L.L. and L.C.; methodology, L.L. and A.P.; formal analysis, L.L., B.T. and A.C.; investigation, L.L.; writing—original draft preparation, L.L. and L.C.; supervision, A.P. All authors have read and agreed to the published version of the manuscript. This research received no external funding. The research infrastructure developed at ICECHIM through the POS-CCE “AGRI-FLUX” project, nr. 645/18.03.2014, cod SMIS-CSNR 48695 was partially used to obtain the results presented in this study. The authors declare no conflict of interest. Figure 1. FTIR spectra of the studied materials. Figure 1. FTIR spectra of the studied materials. Figure 2. SEM images of: (a) Florisil; (b) Florisil after impregnation with Cyphos IL-101; (c) Florisil after impregnation and Pd(II) adsorption. Figure 2. SEM images of: (a) Florisil; (b) Florisil after impregnation with Cyphos IL-101; (c) Florisil after impregnation and Pd(II) adsorption. Figure 3. Bright-field transmission electron microscopy (BFTEM) images of (a) Florisil after impregnation with Cyphos IL-101; (b) Florisil after impregnation and Pd(II) adsorption. Figure 3. Bright-field transmission electron microscopy (BFTEM) images of (a) Florisil after impregnation with Cyphos IL-101; (b) Florisil after impregnation and Pd(II) adsorption. Figure 4. Energy-dispersive X-ray analysis (EDX) spectra of (a) Florisil after impregnation with Cyphos IL-101; (b) Florisil after impregnation and Pd(II) adsorption. Figure 4. Energy-dispersive X-ray analysis (EDX) spectra of (a) Florisil after impregnation with Cyphos IL-101; (b) Florisil after impregnation and Pd(II) adsorption. Figure 5. XPS characterization of the studied Pd-based photocatalyst: (a) XPS wide scan; (b) C 1s and (c) Pd 3D high-resolution spectra. Figure 5. XPS characterization of the studied Pd-based photocatalyst: (a) XPS wide scan; (b) C 1s and (c) Pd 3D high-resolution spectra. Figure 6. UV-vis spectra of the photodegradation process of phenol: (a) photolysis; and photocatalysis in the presence of (b) F; (c) F-IL; (d) F-IL-Pd1; (e) F-IL-Pd2. Figure 6. UV-vis spectra of the photodegradation process of phenol: (a) photolysis; and photocatalysis in the presence of (b) F; (c) F-IL; (d) F-IL-Pd1; (e) F-IL-Pd2. Figure 7. The degradation degree of phenol function of the photocatalyst nature. Figure 7. The degradation degree of phenol function of the photocatalyst nature. Figure 8. The degradation degree of phenol versus the solid:liquid (S:L) ratio. Figure 8. The degradation degree of phenol versus the solid:liquid (S:L) ratio. Figure 9. The degradation degree of phenol versus the photocatalyst reuse. Figure 9. The degradation degree of phenol versus the photocatalyst reuse. Figure 10. BFTEM image and EDX spectrum of the reused photocatalyst. Figure 10. BFTEM image and EDX spectrum of the reused photocatalyst. Figure 11. Degradation kinetics (C/C0 vs. time) of phenol photodegradation process, UV-vis absorption profiles and total organic carbon (TOC) measurements of solutions at certain time intervals. Figure 11. Degradation kinetics (C/C0 vs. time) of phenol photodegradation process, UV-vis absorption profiles and total organic carbon (TOC) measurements of solutions at certain time intervals. Table 1. Elemental concentration resulted from the XPS wide scan spectrum of the studied Pd-based photocatalyst. Table 1. Elemental concentration resulted from the XPS wide scan spectrum of the studied Pd-based photocatalyst. ElementAtomicConc. (%)Mass Conc. (%)C20.2511.91Pd2.7614.39O53.6842.06Si19.4026.68Mg1.852.20P0.320.48Cl0.520.90Na1.221.38 Table 2. Experimental binding energies in eV for the Pd-based photocatalyst (* reference peak). Table 2. Experimental binding energies in eV for the Pd-based photocatalyst (* reference peak). ElementAssignmentBindingEnergy (eV)Relative Conc. (%)C 1 sCaliphatic285 *98.25Chetero286.61.75Pd 3dPd2+337.286.27Pd4+338.513.73 Table 3. Comparison of the photocatalytic efficiency developed by various materials in the degradation process of phenol from aqueous solutions. Table 3. Comparison of the photocatalytic efficiency developed by various materials in the degradation process of phenol from aqueous solutions. PhotocatalystPhenol InitialConcentration, mg/LDegradation Degree, %Treatment Time, minReferencesTitanium dioxide-coated on the inner and outer quartz glass tubes3050300[]Titanium dioxide (TiO2) Degussa P25 (80% anatase, 20% rutile)2083.9360[]ZnO2578.290[]0.5% Pd-0.5% Au/TiO294.11695520[]F-IL-Pd2078.6180Present work Publisher’s Note: MDPI stays neutral with regard to jurisdictional claims in published maps and institutional affiliations. © 2020 by the authors. Licensee MDPI, Basel, Switzerland. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC BY) license (http://creativecommons.org/licenses/by/4.0/). Share and CiteMDPI and ACS Style Lupa, L.; Cocheci, L.; Trica, B.; Coroaba, A.; Popa, A. Photodegradation of Phenolic Compounds from Water in the Presence of a Pd-Containing Exhausted Adsorbent. Appl. Sci. 2020, 10, 8440. https://doi.org/10.3390/app10238440 AMA Style Lupa L, Cocheci L, Trica B, Coroaba A, Popa A. Photodegradation of Phenolic Compounds from Water in the Presence of a Pd-Containing Exhausted Adsorbent. Applied Sciences. 2020; 10(23):8440. https://doi.org/10.3390/app10238440 Chicago/Turabian StyleLupa, Lavinia, Laura Cocheci, Bogdan Trica, Adina Coroaba, and Adriana Popa. 2020. "Photodegradation of Phenolic Compounds from Water in the Presence of a Pd-Containing Exhausted Adsorbent" Applied Sciences 10, no. 23: 8440. https://doi.org/10.3390/app10238440 Find Other Styles Note that from the first issue of 2016, MDPI journals use article numbers instead of page numbers. See further details here. |
