cài đặt bộ điều khiển nhiệt độ Danfoss
tháng 10 30, 2017
Nhận xét
Đăng nhận xét
Bài đăng phổ biến từ blog này
HƯỚNG DẪN SỬ DỤNG BỘ ĐIỀU KHIỂN NHIỆT ĐỘ EKC 102
tháng 10 25, 2017
Đọc thêm
CATALOGUE MÁY NÉN BITZER
tháng 10 24, 2017
Đọc thêm
Quick Links
Installation guide
ERC 213
Digital regulator for refrigeration and defrosting, 3 relays.
Dimensions (mm)
83
Assembly
Wiring diagram
Sair
S5
DO1
1
2
~
~
Electrical input
(on the basis of product code)
© Copyright Danfoss | Published by AZ | 2016.04
The ERC 213 is a smart, multipurpose refrigeration controller with temperature and
defrost management, available with 3 relays. The controller has been designed to fulfil
today's requirements for commercial refrigeration applications.
Assembly
DI1
DI2
DO1
DO2
DO3
Sc
DO2 DO3
3L
4N
5
6
7
~
~
61.2
66
Rear mount (clip fixing)
Programming key - EKA 183B
GND TX
15
16
GND
8
9
10
11
Sair
S5 Sc/DI1
Installation guide | ERC 213
71
29
Drilling template
Removal
RX
+5V
17
18
GND
12
13
14
DI2
DKRCE.PI.RL0.O2.02 / 520H11062 | 1
Summary of Contents for Danfoss ERC 213
ERC213 080G3294 Bộ điều khiển nhiệt độ Danfoss
Danfoss ERC213 là bộ điều khiển làm lạnh đa năng thông minh với quản lý nhiệt độ và rã đông, có sẵn với 3 rơle.Bộ điều khiển đã được thiết kế để đáp ứng các yêu cầu ngày nay của các ứng dụng làm lạnh thương mại.
Loại bộ điều khiển : Gắn bảng điều khiển Kích thước của lỗ gắn : 71×29 mm Đầu ra kỹ thuật : 3 chiếc. Điều khiển : Máy nén Rã đông Quạt Số lượng cảm biến : 2 Sợi Cảm biến / s trong bộ : Có Dãi đo nhiệt độ -40 đến +105 ° C Độ phân giải : 1 K Đầu vào kỹ thuật số : 1 Nhiệt độ hoạt động : -10 đến + 55 ° C Nguồn điện : 230 V, 50 HzCác dòng sản phẩm của Danfoss dienlanhnguyenkhang.com
The ERC 213 is designed to be an easy, universal replacement control. We encourage users to employ one of five predefined applications that meet the
needs of most systems. If users need to modify specific parameters, it should be done after installing the predefined application that most closely meets
system needs.
For more information, including detailed instructions, error codes, parameters, and more,
visit www.danfoss.com/erc or download the Koolcode app from iTunes or Google Play.
For a video guide of the quick set-up, visit //bit.ly/ERC213 or use the QR code located to the right.
Quick Set-up
STEP
Action
STEP 1 Wire control, to include power and sensors
Power up control
STEP 2
Energize control
Enter Quick Configuration Menu and Select app
Press "<" for more than three seconds within one minute of power up to enter Quick Configuration Menu. o61 appears on screen
STEP 3
Press "set" while o61 is on screen
Select appropriate app using App Selection section below by pressing " " or " ", then press "set".
Select Sensor
Press "set" while o06 is on screen
STEP 4
If using included sensor, leave default value "n10". If using another sensor, select using Sensor Resistance
section on opposing page or cycle through steps 2 – 4 changing the sensor type until the temperature reading
on the main screen is accurate. As above, cycle between options by pressing " " or " " and press "set" to save.
Set Temperature
STEP 5
From main screen, quickly press "set" (1 second).
Cycle to intended temperature by pressing " " or " " and press "set" to save.
App Selection
Select application based on application and wiring configuration (i.e., refrigeration vs. freezing, and number of temperature sensors). The Typical Wiring
Configurations diagram on the reverse side of this document may be used to assist with selection. All parameters can be modified using the full menu.
Some parameters have min and max set points which may need to be changed for less common configurations.