cài đặt bộ điều khiển nhiệt độ Danfosstháng 10 30, 2017 Show Nhận xétĐăng nhận xétBài đăng phổ biến từ blog nàyHƯỚNG DẪN SỬ DỤNG BỘ ĐIỀU KHIỂN NHIỆT ĐỘ EKC 102tháng 10 25, 2017 Đọc thêm CATALOGUE MÁY NÉN BITZERtháng 10 24, 2017 Đọc thêm Quick LinksInstallation guide ERC 213 Digital regulator for refrigeration and defrosting, 3 relays. Dimensions (mm) 83 Assembly Wiring diagram Sair S5 DO1 1 2 ~ ~ Electrical input (on the basis of product code) © Copyright Danfoss | Published by AZ | 2016.04 The ERC 213 is a smart, multipurpose refrigeration controller with temperature and defrost management, available with 3 relays. The controller has been designed to fulfil today's requirements for commercial refrigeration applications. Assembly DI1 DI2 DO1 DO2 DO3 Sc DO2 DO3 3L 4N 5 6 7 ~ ~ 61.2 66 Rear mount (clip fixing) Programming key - EKA 183B GND TX 15 16 GND 8 9 10 11 Sair S5 Sc/DI1 Installation guide | ERC 213 71 29 Drilling template Removal RX +5V 17 18 GND 12 13 14 DI2 DKRCE.PI.RL0.O2.02 / 520H11062 | 1 Summary of Contents for Danfoss ERC 213ERC213 080G3294 Bộ điều khiển nhiệt độ Danfoss Danfoss ERC213 là bộ điều khiển làm lạnh đa năng thông minh với quản lý nhiệt độ và rã đông, có sẵn với 3 rơle.Bộ điều khiển đã được thiết kế để đáp ứng các yêu cầu ngày nay của các ứng dụng làm lạnh thương mại. Loại bộ điều khiển :Gắn bảng điều khiểnKích thước của lỗ gắn :71×29 mmĐầu ra kỹ thuật :3 chiếc.Điều khiển :Máy nénRã đôngQuạtSố lượng cảm biến :2 SợiCảm biến / s trong bộ :CóDãi đo nhiệt độ-40 đến +105 ° CĐộ phân giải :1 KĐầu vào kỹ thuật số :1Nhiệt độ hoạt động :-10 đến + 55 ° CNguồn điện :230 V, 50 HzCác dòng sản phẩm của Danfoss dienlanhnguyenkhang.com The ERC 213 is designed to be an easy, universal replacement control. We encourage users to employ one of five predefined applications that meet the needs of most systems. If users need to modify specific parameters, it should be done after installing the predefined application that most closely meets system needs. For more information, including detailed instructions, error codes, parameters, and more, visit www.danfoss.com/erc or download the Koolcode app from iTunes or Google Play. For a video guide of the quick set-up, visit http://bit.ly/ERC213 or use the QR code located to the right. Quick Set-up STEP Action STEP 1 Wire control, to include power and sensors Power up control STEP 2 Energize control Enter Quick Configuration Menu and Select app Press "<" for more than three seconds within one minute of power up to enter Quick Configuration Menu. o61 appears on screen STEP 3 Press "set" while o61 is on screen Select appropriate app using App Selection section below by pressing " " or " ", then press "set". Select Sensor Press "set" while o06 is on screen STEP 4 If using included sensor, leave default value "n10". If using another sensor, select using Sensor Resistance section on opposing page or cycle through steps 2 – 4 changing the sensor type until the temperature reading on the main screen is accurate. As above, cycle between options by pressing " " or " " and press "set" to save. Set Temperature STEP 5 From main screen, quickly press "set" (1 second). Cycle to intended temperature by pressing " " or " " and press "set" to save. App Selection Select application based on application and wiring configuration (i.e., refrigeration vs. freezing, and number of temperature sensors). The Typical Wiring Configurations diagram on the reverse side of this document may be used to assist with selection. All parameters can be modified using the full menu. Some parameters have min and max set points which may need to be changed for less common configurations. |